Haltech F10X Manual de usuario Pagina 117
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
F10X Manual
117
Adjustable Features
•
Base Fuel Map
22 Fuel ranges, every 500 RPM to 10,500, or
17 Fuel ranges, every 1000 rpm to 16,000
32 Load points per range, up to 16ms with 0.016ms resolution
•
Corre ction Maps
•
Fue l
Cold Start Prime - 32 points
Coolant Temperature Enrichment - 32 points
Air Temperature Adjustment - 32 points
Battery Voltage Correction - 32 points
Closed Throttle (selectable) - 16 points
Full Throttle (selectable) - 32 points
•
Programmable Rev-Limit
•
••
•
Fuel Cut on Deceleration
•
Accelerator Pump
Increase and sustain parameters
Coolant enrichment factor
Three speed ranges
•
Idle Speed Control
Target Idle Speed
Cold Idle-up Rpm
Post-start Rpm setting
•
Closed Loop Control
With both cruise and idle settings
•
Programmable Output Options
Miscellaneous
•
Data logging
Engine data information logged at a nominal rate of 10 times per second Stored to memory or disk
Limited only by available memory (approx. 11k/minute).
•
Map Storage and Retrieval
Maps may be stored to disk and re-used.
•
Real Time Programming
Instant, hesitation free adjustment while engine is running.
- Warning 1
- Contents 2
- Introduction 7
- Tool/Supply Requirements 8
- How It Works 9
- SECTION 1 Getting Started 11
- Mounting 13
- 1.3.7 Power Relays 16
- 1.3.8 Fuse Block Assembly 17
- 1.3.10 Flying Leads 18
- 1.3.14 Connect the ECU 20
- 2.1 Computer Requirements 21
- 2.2 Operating the Software 21
- 2.2.2 Running the Software 23
- 3.1 The Menu Structure 24
- 3.1.1 The File Menu 24
- 3.1.1.1 Load From File 25
- 3.1.1.2 Save To File 25
- 3.1.1.4 Quit 26
- 3.1.2 The Map Menu 27
- The Set-up Menu 29
- 3.1.3 The Options Menu 29
- 3.1.4 Data Page Menu 30
- 3.1.5 Password Protection 30
- 3.2.1 Going Online 31
- 3.3 Hot Key Summary 33
- 4.2 The ECU Set-up Pages 34
- 4.2.1 Main Set-up Page 34
- 4.2.2 Fuel Set-up Page 36
- 4.2.3 Trigger Setup 39
- 4.2.4 The In/Out Set-up Page 39
- CHAPTER 5 HALTECH MAPS 43
- 5.1 What are Maps? 43
- 5.2.2 All Ranges 45
- 5.2.3 Percentage Changes 45
- 5.2.4 Linearise 46
- 5.2.5 Numeric Mode 47
- 5.2.6 3D View 48
- 5.3 The Haltech Maps 49
- 5.3.2 Fuel Correction Map 49
- 5.3.2.4 Fuel Priming Map 50
- 5.3.2.5 Post Start Map 50
- 5.3.2.7 Gas Pressure Map 50
- 5.3.2.8 Gas Temperature Map 50
- 5.3.3 Zero Throttle Map 51
- 5.3.4 Full Throttle Map 51
- 5.3.5 Turbo Waste-gate Maps 51
- 5.4 Dual Maps 52
- 5.4.1 Editing Dual Maps 52
- SECTION2 Tuning The Engine 53
- 6.3.4 Tuning for Idle 55
- 6.3.5 Tuning with No Load 55
- 6.3.6 Loading the Engine 56
- 6.3.7 Fine Tuning the Engine 56
- CHAPTER 7 THROTTLE EFFECTS 58
- 7.1 Throttle Response 58
- 7.2 Zero Throttle Map 59
- 7.3 Full Throttle Map 59
- 8.1 Cold Cranking 60
- 9.1 Fuel Versus Air Temp Map 61
- 9.2 The Battery Voltage Map 61
- 9.3 Barometric Correction 62
- 9.4 Post Start Enrichment 65
- SECTION 3 Software Features 66
- 10.1.3 Logging the Data 67
- 10.1.4 Displaying The Data 68
- 10.1.4.1 Displaying Channels 69
- 10.1.4.4 Removing A Dataset 70
- 10.1.4.5 Data Values 71
- 10.1.4.6 Zooming 71
- 11.1 Idle Speed Control and O 74
- Closed Loop Control 74
- 11.1.1 Idle Control 74
- 11.2 The PWM Options Page 78
- 12.11 Turbo Timer (TT) 83
- 12.12 NOS Switch 83
- 12.13 Air Conditioning 84
- 12.14 Engine Control Relay 84
- 12.15 VTECH 85
- 12.16 BAC2 85
- 12.18 TPS Switch 86
- SECTION 5 Appendices 88
- A.1 Control Program Problems 89
- A.3 Starting problems 90
- A.4 Idling Problems 90
- A.6 Full Power Problems 91
- A.8 Cold Running Problems 91
- A.9 Fuel Consumption 91
- B.1 Distribution of Outputs 93
- B1.1 Multipoint Injection 94
- B1.2 Batch Injection 94
- B1.3 Staged Injection 95
- B.2 Rotary Engines 96
- APPENDIX C INJECTORS 97
- C.1 Injector Impedance 97
- C.2 The Injector Drivers 97
- D.1 Duty Cycles 98
- D.2 Fuel Requirement 100
- D.3 Injector Flow Capacity 100
- D.4 Injector Staging 100
- D.5 Fuel Pump Capacity 101
- E.1 The Trigger Type 103
- E.1.2 Hall Effect Sensors 104
- The S3 Hall Effect Sensor 105
- SENSOR PIN OUTS 105
- E.1.5 Typical set-ups – S3 106
- 8 Cylinder Engine 107
- E.1.6 Checking the Sensor 108
- Coil Negative/Tacho Output: 110
- ( Pin 36 on ECU) 110
- E.3 Tacho Output Triggering 111
- E.4 Trigger Edge 112
- E.5 Trigger Pull up 114
- F10X Manual 118
- F10X Hardware Options 118
- LIMITED WARRANTY 119
- APPENDIX H WIRING DIAGRAMS 120
Relacionado con productos y manuales para Para El Coche Haltech F10X
Para El Coche Haltech F10 Manual de usuario
(104 paginas)
(104 paginas)
Para El Coche Haltech IG5 Manual de usuario
(89 paginas)
(89 paginas)
Para El Coche Haltech E6A Manual de usuario
(126 paginas)
(126 paginas)
Para El Coche Haltech E6S Manual de usuario
(134 paginas)
(134 paginas)
Para El Coche Haltech E6GMX Manual de usuario
(114 paginas)
(114 paginas)
Para El Coche Haltech E6M Manual de usuario
(152 paginas)
(152 paginas)
Para El Coche Haltech E6K Manual de usuario
(154 paginas)
(154 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales